cot bed plans blueprints Cot bed plans blueprints

There are few occasions that inspire the potential builder more than the immanent birth of a baby. I am no exception, and since I am due to have a new child in March, last month I decided to make a crib. There are strict governmental guidelines regarding the construction and design of cribs. The details I was most concerned to find were the spacing of bars and the height of the mattress.

This project is a good example of one that requires fairly careful planning. More than just having enough material and a rough-and-ready plan my version usually scrawled on a single piece of paper , in this instance there cannot be any last-second design choices. So I advise not only planning every detail carefully but you should also but the mattress and base the dimensions off its size. The space between the slats or bars cannot exceed two and three-eighths inches.

I made them slightly closer together, at two and one-eighth. I decided to have three sides made using frame and panel construction and one side with bars. They are easy to find and strong enough for this use. These dowels, by regulations, are not allowed to turn or move in any way. I decided that there should only be two mattress heights.

The lowest position has to have the bottom of the mattress at least 26 inches from the lowest point of the top of the crib.

The highest position has to have the mattress at least 9 inches from the lowest point of the top of the crib. The material list ends up being not very expensive: The first task was to cut all the various widths and lengths.

Pieces were cut to length using the mitre saw and a stop block. I always try to double check that my measurements are allowing for the tenons on the ends of these frames. A common mistake is to cut off members of a frame at the visible dimension, even if you are the person who made the design.

With all of the pieces cut to size, the next task was to set up for cutting dados and rabbets.

  • baby cot bed tesco
  • cot bed duvet cover dunelm mill
  • cot bed bedding sets mamas and papas
  • By doing so, you completely centre the dado. All the pieces should fit together easily. With all of these pieces cut and set out, it is then a good idea to set up the router table and ease the edges of every piece. The faces with dados in them will not be easy to sand once the panels are assembled: All of that can then be set aside.

    It took me an hour or two to cut all of these pieces.

    baby cot with adjustable side

    Prior to anything else, the system for supporting the mattress needs to be started. One set of slots would be for the high mattress position, the other set for the lower. These need to be carefully marked out so they all match. I found it necessary to use a small drum sander inside the cut-out to get it completely smooth. Then I used a roundover bit in the router to ease the edges.

    I began with the back panel. I used polyurethane glue but wood glue is perfectly fine. Polyurethane glue expands and fills any sloppiness of your joints.

    My joints were not bad but there was some variation in the thickness of the poplar, which threw off the thickness of the grooves and tongues and tenons a little. That said, cleaning the foamed-out polyurethane glue the next day is not a pleasant task. But once I was done, I assembled the end panels of the crib. While that was drying, I cut all the dowels to length and drilled the holes in the front rails. I started by marking the centre and then spacing the holes two and three-quarters on centre.

    That works out to having a two and one-eighth inch gap between the bars. I must admit, I cheated a little with the design of this crib. I knew there might be some aggravation trying to get everything to line up top and bottom. In fact, I planned the whole thing for straightforward building. The dados in the vertical supports for the end panels continue down to the floor and needed to be filled.

    This is not really the most acceptable thing to do if you plan on staining or some other natural finish.

    Facebook fan Idriaan Stander shared this photo with us, featuring two train car beds, with Thomas the Tank Engine leading the charge. The major draw back to this is when it comes time for assembly.

    But the crib was to be painted. Assembling the rails with the dowels to make up the front of the crib was a little different from everything else. I used the rails for the front as spacers to hold the crib square while the glue dried.

    This was all done with the crib upside-down on the floor. That proved to be the easiest way to line up the parts. Once that glue was dry, I glued together the front bar-assembly of the crib with the rails inserted in the dados of the end panels. That is, I used the glued-up three sides of the crib to hold the rails square to the bars while the glue set.

    I needed to apply clamping force to hold the rails onto the dowels, so it was not a good idea to try to glue the entire front of the crib at once. Rather, I let the rail and bar assembly glue set and then glued the entire thing into the crib. Once again, I used polyurethane glue. These dowels are fairly consistent, but there is a bit of variation in diameter. There was less glue to clean up than I expected.

  • yellow cot bed duvet cover
  • cheap cots for sale
  • cot bed duvet cover size
  • And there was also very little sanding to do, since I had made a point of sanding all the pieces before assembling them. So I could then turn my attention to making the parts to support the mattress. I cut two pieces of wood long enough to have an inch sticking out each support slot in opposite ends of the crib. I marked these pieces just at where they reached the inside of end panels of the crib. I then cut notches large enough for pieces of poplar to drop in. This makes it impossible for the supports to be knocked out but also makes it easy to relocate them.

    The piece of mdf that holds the mattress up has two finger-holes in it to make it easy to remove. There are also two cross-supports in the middle of the span of the main support, and these should be screwed in place if they ever seem likely to fall. These would be the only screws in the entire build. All parts complete, the crib gets a few coats of paint.

    This plan is for a wooden crib that meets all current safety standards.

    cot bed plans blueprints Cot bed plans blueprints

    It has two mattress heights and is made using frame-and-panel construction for three sides, with bars on the front. There is no complex joinery, nor is there any specialty hardware required to build it. The design is straightforward, however it would make a good base for those who would like to add detail. Suggested materials for this project are poplar and mdf.

    However, other woods are equally suitable. Once assembled, this crib will be a safe and comfortable place for a very long time.

    cot bed plans blueprints Cot bed plans blueprints

    Comment

    Kajimuro

    at 22:00

    I am sorry, it not absolutely that is necessary for me. Who else, what can prompt?

    Sasar

    at 22:03

    In it something is. Thanks for an explanation. I did not know it.

    Gardat

    at 22:43

    What necessary phrase... super, a brilliant idea

    Grozshura

    at 10:44

    Actually. Tell to me, please - where I can find more information on this question?

    Leave a Comment