Children Featured 20 Comments 0 Materials: Optional — Kreg Pocket hole drill jig. After no luck finding any company that makes a toddler sized platform bed, I decided to make one. She also has no issues rolling out of bed. If you make this for you kid, make sure they are ok climbing in, out, and sleeping in it.
Assemble the Gulliver bed frame. Leave the mattress support slats off for now. Note that you need to leave off the two metal tie rods that link the front and back of the bed, as well as the four screws that prevent the bed slats from sliding around.
These would all interfere with the cabinets. I chose to just screw the bed slats down once complete. It serves the same purpose.
Prevent frame flex and slats from sliding. Assemble the two Besta cabinets. These are are the Besta units of the following measurements: Measure and mark up. Prop the bed frame so that the two cabinets are under each side of the front of the bed. Use the two doors to prop up the back temporarily. The unfinished wooden rail that the mattress slats sit on is what will rest on the cabinets.
With the cabinets slid as far to each side as they can go, and butted up to the front frame, mark up the inside of the legs for where to cut. Note that the legs are not a straight-forward cut. The front is cut to the level of the front of the bed frame.
Cut to the level of the wooden bar, not the bed side. Note in the picture the slight gap it leaves. The easiest way to do this is to cut the lower cut all the way across. Once you have the shortened frame end, you can cut the vertical cut in from the end and the higher horizontal cut from the back side to cut out the notch. I made the rear legs out of two sections of one of the doors cut to size. The doors are a few eighths of an inches shorter than the cabinets, so you can NOT just cut a couple of strips for new back legs.
Cut and measure two correct length legs from the door turned vertical. Or make legs from some scrap wood if you like, so long as they are the same height as the cabinets. Screw main parts together. Slide the cabinets under the bed so they now sit in line with the end of the bed frames. Refer to that close-up picture again.
Screw the bare wooden frame to the cabinets. I chose to do this from underneath, and countersunk the holes. That way screw heads will not interfere with the bed slats. Screw the back legs on. With bare wooden rail resting on the legs, screw the legs into the frame from the front.
You can now put the drawers and shelves in the cabinets. I cut two of the Vikare rails to length so that they left a gap the same width as the gap between the cabinets. With the hardware fitted, the cut end is placed flush against the bed frame, leaving the factory rounded ends in the middle. I re-drilled new holes for the hardware the same distance from the end of the cut section of the rail as the factory holes are from the uncut end.
Your angle may depend on how far out you want the steps to protrude out. The steps themselves are just straight cuts sections of Vikare guards. To avoid having screws visible on the outside of the rails, I used the pocket hole cutter to drill two hidden holes in each side of each step, on the underside. They are then screwed in through those holes into the sides.
I didn't realize how much I appreciate mine until I spent the weekend at my parent's house with my baby, my back was killing me from bending over to change her on the bed, couch, or floor. Considering how many times a day an infant needs their diaper changed it is definitely worth it.
The ladder is secured to the cabinets using screws through the factory holes where the rail hardware would have been fitted.
I used the second door to panel in the the back of the gap between the two cabinets. Put the bed slats on the bed and secure the end slats in place to the wooden rail with a couple of screws.
Put the mattress on. I chose not to panel in the sides completely, behind where the cabinet sides stop. You could buy a couple of extra doors and cut sections to fill the gaps.
I also still need to round off edges where I cut parts, so that they will match the chamfered factory edges. I intend to paint them white with matching semi-gloss finish to neaten the whole thing up.
В© 2016 - 2018 Business_Blog. All rights reserved | Template by W3layouts